Ricoma TC-1501 Common Issues And Simple Maintenance

 

Ricoma TC- 1501 Common Problems And results

1. A New Design Is Not Uploading

You have to remove the embroidery status before uploading a new design. The status of embroidery( the cinch icon in the panel) is the tool that sets the machine in and out of embroidery mode.

The status of the embroidery icon could be set up on the right corner of the screen and must be uncorked to pierce some of the machine’s features. Another cause you might not be able of importing a design is if the USB you're using has inordinate memory. We suggest using a USB drive with 8 GB or lower most popular embroidery designs.

2. Needles Keep Breaking

There are several reasons why needles in a Ricoma TC- 1501 machine may break

Incorrect Needle Size Or Type – Make sure you're using the correct size and type of needle for the material you're working with.

Needle Dullness – Over time, needles can come dull, especially if you're using them to exaggerate thick, heavy accoutrements . Dull needles can break more fluently than sharp bones .

inordinate Pressure – If you're applying too important pressure when stretching, you can put a lot of stress on the needle and beget it to break best fabric for machine embroidery.

Thread Pressure Issues – Incorrect thread pressure can beget the needle to bend, causing it to break more fluently.

Loose Needle Clamp – If the needle clamp is loose, the needle can move and bend, causing it to break.

Machine Issues – There may be a problem with the machine itself, similar as a misaligned needle bar or a worn-out needle drive medium.

3. Pinch On Fabric

This is because of a hooping error. You have to produce the right pressure by icing that the hooping is tight and the material isn't crinkled. Be specific not to stretch the fabric, as this could damage the design. You might need a establishment stabilizer best embroidery machine for custom designs.

4. Thread Breaks

There are several reasons why you may be passing thread breaks while using a Ricoma TC- 1501 machine

Incorrect thread type – Make sure you're using the correct type of thread for your machine and the material you're working with.

Incorrect thread pressure – If the thread pressure is too loose, the thread may breakeasily. However, it can put stress on the needle and beget it to break, If the pressure is too tight.

Poor thread quality – Low- quality thread can fluently break, so be sure to use high- quality, durable thread for your machine Embroidery digitizing service.

Dirty machine – Dust and debris in the machine can beget thread to break. Clean your machine regularly to keep it in good working order.

Needle issues – A dull or damaged needle can beget thread to break. Replace the needle if it's worn or damaged.

Bobbin issues – Make sure the bobbin is loaded rightly and the pressure is set rightly. A inadequately wound bobbin or one with low- quality thread can beget thread to break.

Stabilizer issues – If you're using stabilizer, make sure it's the correct type and weight for the material you're working with. However, it can put too important stress on the thread, causing it to break, If it's too heavy Embroidery digitizing.

5. How To Know If The Pressure Is Right? Is There Any dereliction Setting?

There's no similar dereliction setting on the machine at the sametime.However, you can start by pulling the thread and feeling its pressure, If the problem is on a single needle. It mustn't be veritably tight or veritably loose.

Check the needles that are operating correctly and try to mimic their pressure. As you pull, you must be able of feeling when the problem needle has reached a analogous pressure as the needles that are working well embroidery machine fabric.

Once you believe you have attained a good standard pressure, try an H or I test during the middle and one- third of the top thread on both sides. generally, if you have one- third of the bobbin thread in the center and one- third of top thread on both sides. generally, if you have fairly given columns, your pressure must be correct machine embroidery on balsa wood.

6. Aches Deviating

Deviating aches could be the outgrowth of incorrect threading. insure the top and bobbin vestments are correctlythreaded.However, check the thread pressure, If the machine is threaded correctly. Plus, insure to check the needle. A fraudulent, old, or loose needle would beget looping and other embroidery issues best embroidery machines for custom designs.

7. X Or Y Limit Error

You're getting this error because your totem might be veritably huge for the circle, or you're trying to sew out the preset circle periphery. You can moreover use a large circle or move the totem around so you stay within the boundaries of the circle.

EASY way FOR RICOMA TC- 1501 MAINTENANCE

Ricoma TC- 1501 conservation is veritably easy. The most pivotal conservation that has to be completed is slicking the rotary hook. Before slicking or drawing, we suggest turning off your machine. To maintain and clean the rotary hook, begin by removing the bobbin case from the rotary hook what fabric is best for embroidery.

Clean any thread fur in the area using a fur encounter or dusting spray.

also add three or four drops of machine oil painting to the rotary hook.

Now you can fit the bobbin case back into the rotary hook and close the bobbin casing unit.

To make sure the machine runs efficiently, repeat this process twice a day if you're planning to run a machine eight hours a day.

Once or twice a week, remove the needle plate and clean around the trimmer shanks with a soft encounter.

Once a week, pass a business card or paper through the bobbin case slit to clean any fur buildup.

Every week, place a drop-off oil painting directly on the needle bar through the places in the needle case, alternate each week.

One week slick the upper needle bar section and the coming week the lower needle bar section.

Once a week oil painting the opening on the needle plate. For this section, we suggest turning on the machine and setting it to needle one to see the opening on the right side of the machine head.

Add three drops of oil painting each week to that section.

also, add three drops of oil painting to the essence rail of the machine head.

Now you can move your machine head to needle 15 and place 2 drops of oil painting on the other side of the rail.

Once each three to five months, apply white lithium grease to the black essence bar in the machine head. Also, apply this grease to the bus placed on the reverse of your machine head.

Once each three to five months, apply white lithium grease to the color change cam.

You would first need to remove the essence plate placed above the color change cam by loosening the attached screw. also apply grease to the color change cam area.

Place the cover back over the color change cam and strain the screw before pacing.

Always flash back , not to over oil painting. After slicking, sew on a test belt before returning to product to assure redundant oil painting doesn't stain garments.

These were the simple way for Ricoma TC- 1501 conservation and troubleshooting Ricoma TC- 1501 embroidery machine. Now that you veritably well know how to maintain your machine, it's time to start stretching. Good luck!

Winding Up With Offer

We hope this composition will be helpful foryou. However, as digitizing is a complex process, If you want to digitize embroidery design you would need a professional like ZDigitizing.

Zdigitizing

is a digitizing embroidery company that provides complete Embroidery digitizing services and vector art services each over the world to businesses, diligence, and pots.

So, if you need a digitizing or vector art service for your embroidery machine, with a super-fast reversal and excellent quality, zdigitizing will be your stylish choice. Just click the link below and get a free quotation in lower than 5 twinkles. We offer 50 out on all our services to our implicit guests on their first order.

Hope it'll be helpful for you guys!

If there’s any question related to this composition you can simply ask in the comment section and do n’t forget to partake with those you suppose might be helpful for them.

And eventually, thanks for reading!

You Can Get 50% off Using This Coupon Code: james50off Applied Coupon link: https://zdigitizing.com/product-category/services/?coupon-code=james50off